软β核素内部样品塑料闪烁探测器

本文评价了塑料闪烁片用作软β核素探测器时的计数效率、β谱、本底谱和康普顿电子谱的特征。文中强调:采用胶合光导剂构成的系统是一种新型探测器(软β核素内部样品塑料闪烁探测器)。本文提出内部样品固体探测器、胶合光导剂和胶合闪烁光导剂的新概念。     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

BC480-22/42支架液压系统的大流量技术改造

分析了BC-480支架在综采工作面使用中液压系统配置低的原因,提出了系统的改造原则和方案,比较了改制前后支架的动作速度.     

Fracture toughness of thermoset composites reinforced by perfectly bonded impenetrable short fibers

The fracture toughness of brittle thermoset resins could be improved significantly by perfectly bonded tough, short fibers through both crack trapping and bridging effects. In this paper, the crack trapping effect was studied through the analysis of the change of strain energy associated with the crack propagation across a regular array of fibers, and the bridging effect was discussed based on the Andersson–Bergkvist model. The fracture resistance increases with the fiber volume fraction, and is independent of the elastic properties of the matrix, the crack length, and the cross-sectional diameter of the fibers.     

Robust State Feedback Control Through Actuators With Generalized Sector Nonlinearities And Saturation

In control systems, actuators often have nonlinear characteristics that can not be neglected. For linear systems driven by actuators satisfying the generalized sector condition, a robust state feedback controller synthesis method is proposed to achieve the ultimate boundedness control. The method is based on the linear matrix inequality approach and is easy to apply. As an important special case of the generalized sector condition, the saturation characteristic of actuators is discussed separately, and non‐conservative results are obtained.     

产量递减规律的诊断方法

传统的Arps产量递减分析方法要求事先选定递减规律的初始时间、初始产量及初始递减率,事实上这些参数是很难确定的。实际应用时不得不人为地加以臆断而使得此方法带有不确定性.为此提出了产量递减规律的诊断方法。应用诊断曲线很容易确定递减规律的模型参数,克服常规方法的不足。通过选用参考时间、参考产量和参考递减率,使得递减分析方法具有一定的灵活性和优越性、该方法简便、实用。     

Diurnal thermal cycling effects on microwave signatures of thin seaice

To investigate effects of diurnal thermal cycles on C-band polarimetric backscatter and millimeter-wave emission from sea ice, the authors carried out a winter experiment at the outdoor geophysical research facility (GRF) in the cold regions research and engineering laboratory (CRREL), the ice sheet grew from open sea water to a thickness of 10 cm in 2.5 days, during which they took polarimetric backscatter data with a C-band scatterometer, interlaced with brightness temperature measurements at 90 GHz in conjunction with meteorological and sea ice characterizations. The initial ice growth in the late morning was slow due to high insolation. As the air temperature dropped during the night, the growth rate increased significantly. Air temperature changed drastically from about -12 to -36°C between day and night, the diurnal thermal cycle repeated itself the next day and the growth rate varied in the same manner. Ice temperature profiles clearly show the diurnal response in the ice sheet with a lag of 2.5 h behind the time of the maximum short-wave incident solar radiation. The diurnal cycles are also evident in the millimeter-wave brightness temperature data, measured sea ice backscatter revealed substantial diurnal variations up to 6 dB with repeatable cycles in synchronization with the temperature cycles and the brightness temperature modulations, the diurnal cycles in backscatter indicate that the dominant scattering mechanism related to thermodynamic processes in sea ice is reversible, a diurnal backscatter model based on sea ice electrodynamics and thermodynamics explains the observed diurnal signature. This work shows that diurnal effects are important for inversion algorithms to retrieve sea ice geophysical parameters from remote sensing data acquired with a satellite synthetic aperture radar (SAR) or scatterometer on Sun-synchronous orbits     

基于空间矩的灰度边缘亚像元度量精度分析

灰度图像中边缘定位受采样密度限制，亚像元精度度量方法在需要高精度的应用中受到重视，要想知识到底需要多高的分辨率才能达到定精度指标，就有必要分析特征定位方法的最坏情况的精度，文中用分析和实验的方法给出了基于空间矩的边缘定位方法，对于边缘点，边缘直线以及直边缘区域的最坏情况定位精度分析。分析和讨论的结果不但可以用来确定已知形状位置估计的最大误差，而且还可用于对准的形状几何参数，以获得较高的精度。     

浅淡技术情报在企业技术创新中的重要性

介绍技术情报在企业技术创新中的重要性和支撑作用,提出了两种创新模式中技术情报收集应注意的问题。